Audio DX2040 Manuel d'utilisateur télécharger pdf

Controls, display

and connections

Battery compartment

Holds two 1.5v AA (LR6) type cells.

On/Off

Switches the power on or off. Additionally the output cable

includes a link which disconnects power when the Lemo

plug is removed, in which case the switch can be left on.

Identification plug

Can be fitted with one of the coloured rubber plugs supplied

with the DX2040 to identify each unit.

Audio output

Provides transformer balanced microphone level and

adjustable headphone outputs.

Antenna A and Antenna B

SMA sockets to which the antennae are connected.

Indicators next to each antenna indicate which of the unit’s

two built-in receivers is active at any time.

Infra-red port

Receives commands from and transmits status information

back to the SwitchIR infra-red controller.

TX/DX low battery indicators

Illuminate when the unit detects low battery power in either

the TX2040 Pocket Transmitter or DX2040 Receiver. The

units should not be used when a low battery power indicator

is illuminated as poor operation may result.

Note: The low DX battery indicator does not function when

the receiver is externally powered via Audio Ltd’s cables.

This is not a fault.

No-signal indicator

Illuminated when no carrier signal is being received, such as

when the transmitter is switched off or set to an incorrect

frequency.

To set up the DX2040 in conjunction

with a TX2040 or HX2040:

•

Fit the batteries.

•

Connect the A and B antennae.

•

Connect the audio output cable.

•

Slide the On/Off switch to the On position.

•

Select the operating frequency.

•

Set the output level.

•

Check that one of the A and B indicators is illuminated

and that the red ‘No signal’ indicator is not illuminated.

These steps are explained on the following page:

User Guide DX2040 True Diversity Receiver

The 2040 range has been designed as a result of extensive feedback from professional sound specialists

and sets a new benchmark for radio microphone systems, with several unique features and offering

benefits to appeal to sound mixers, directors, and artists.

The DX2040 true diversity receiver in the RMS2040 range can be used with the TX2040 pocket

transmitter and the HX2040 handheld transmitter. It is also fully compatible with the TX2020 and

TX2000 UHF transmitters. All settings on the DX2040 receiver can be read or changed via infra-red

using the Switch

or AudiR© for Palm™.

Bottom panel

Battery

compartment

Identification

plug

On/off switch

Top panel

Antenna B

No signal

Audio

output

Antenna B

Infra-red port

TX low

battery

DX low

battery

Bottom panel

Battery

compartment

Identification

plug

On/off switch

Top panel

Antenna B

No signal

Audio

output

Antenna B

Infra-red port

TX low

battery

DX low

battery

1 2 3

Résumé du contenu

Page 1 - Controls, display

Controls, display and connectionsBattery compartmentHolds two 1.5v AA (LR6) type cells.On/OffSwitches the power on or off. Additionally the output cab

Page 2 - Setting up the DX2040

Fitting the batteriesTo open the battery compartment, slide the release catch towards the centre of the DX2040 and flip open the cap

Page 3 - Technical specification

TxRxRx Tx BAtt2.7 vH• Align the front of the SwitchiR with the infra-red port on the receiver and press OK. The display will show the DC volta

Commentaires sur ces manuels

Pas de commentaire

Audio DX2040 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Récepteurs et amplificateurs Audio DX2040. Audio DX2040 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels